Mirage 2000 Modelsvit Pérou

1
April 4, 2021
2
April 4, 2021
3
April 4, 2021
4
April 4, 2021
5
April 4, 2021
6
April 6, 2021
The canopy is not positioned correctly, the visor of the dashboard is too thick, it will be necessary to refine this
7
April 6, 2021
I sanded the underside of the visor and retracted it to limit the risk of interference with the canopy
8
April 6, 2021
9
April 6, 2021
the rendering of the nozzle is correct, in resin it must be thinner ... but it increases the cost of the kit
10
April 6, 2021
11
April 6, 2021
12
April 6, 2021
13
April 6, 2021
the two generations of Dassault deltas, they are almost the same size!
14
April 15, 2021
15
April 15, 2021
Decals Ok, Just a little strip of hatched decal to pick up
16
April 15, 2021
And here he is on his feet
17
April 17, 2021
18
April 17, 2021
19
April 17, 2021
20
April 17, 2021
21
April 17, 2021
22
April 29, 2021
23
April 29, 2021
I put the traces of hydraulic fluids
24
April 29, 2021
once all the probes and antennas are in place, I don't know where to handle it ...
25
April 29, 2021
there are even two probes at the bottom of the fin, one on each side
26
April 29, 2021
there are also the antennas, and one of the probes on the cockpit ends has already disappeared ... found and to be re-glued!
27
April 29, 2021
An ejection seat to finish plus a stroke of satin varnish and this 2000P mirage will be finished.
28
May 2, 2021
29
May 2, 2021
30
May 2, 2021
31
May 2, 2021
32
May 2, 2021
33
May 2, 2021
34
May 2, 2021
35
May 2, 2021
36
May 2, 2021
37
May 2, 2021

Komentáře

17 4 April 2021, 19:16

Prieur Gaël
It is a very easy and pleasant assembly, no trap for the moment.
I used the color of the cockpit which is not black for the first machines but blue gray (gunze H337)

4 April 2021, 19:25

Maciej Bellos
That's a rare sight! A perouvian Mirage! Looking good!

17 April 2021, 14:18

Laurent VILLANUEVA HELLER ForEver
good job !

17 April 2021, 16:03

Prieur Gaël
merci laurent
@Maciej I loved to see the french airplane with exotic scheme

17 April 2021, 17:48

Pierre-Christian Baudru
Bravo Gael !

18 April 2021, 05:55

Prieur Gaël
Merci Pierre

18 April 2021, 16:04

Laurent VILLANUEVA HELLER ForEver
pas eu trop de mal avec la découpe du kit ( dessous? )

19 April 2021, 16:47

Prieur Gaël
Non pas trop, il me sert de montage de déverminage, je repère des trucs pour ceux qui suivront,comme limer certaines parties des entrées d'air (sur le dessous) qui gène un peu la bonne pose du ventre et crée une petite marche juste derrière la case de tain

20 April 2021, 17:33

Laurent VILLANUEVA HELLER ForEver
ok...la découpe du bas est bizarre , mais sinon le kit est très détaillé

20 April 2021, 18:35