Big Viggen
Kommentare
59 21 September 2022, 13:49
Gary Victory
That's a really great build and finish Sasa, the masking alone must have been a labour. Top job Sir. 👍👍👍
That's a really great build and finish Sasa, the masking alone must have been a labour. Top job Sir. 👍👍👍
21 September 2022, 13:55
Neil
I agree with Gary. This is just stunning work! Who doesn't love a Viggen in splinter camo AND this one is 1/32 too! 🙂 👍
I agree with Gary. This is just stunning work! Who doesn't love a Viggen in splinter camo AND this one is 1/32 too! 🙂 👍
21 September 2022, 14:40
Erik Off
Fantastic job! 👍 Mine still hasn't been sent and you already have it finished. 😄
@John: It has long been sold out. Jetmads only makes 500 of a model, which you should pre-order. Currently it is the turn of the Stiletto.
Fantastic job! 👍 Mine still hasn't been sent and you already have it finished. 😄
@John: It has long been sold out. Jetmads only makes 500 of a model, which you should pre-order. Currently it is the turn of the Stiletto.
21 September 2022, 18:50
John Hughes
Thanks, Eric. Yes, I'd been looking at Ebay for these. Jetmads is not a company I know, but having had a look at their website and seeing the prices, I think I'll pass!
Thanks, Eric. Yes, I'd been looking at Ebay for these. Jetmads is not a company I know, but having had a look at their website and seeing the prices, I think I'll pass!
21 September 2022, 19:32
Erik Off
Yes, 260€ including shipping are hefty.
3D- and resin-parts are unfortunately always a bit more expensive.
Yes, 260€ including shipping are hefty.
3D- and resin-parts are unfortunately always a bit more expensive.
21 September 2022, 19:57
Erik Off
Mine arrived yesterday. 👍 😄
Sasa, do you have any tips for the construction?
Mine arrived yesterday. 👍 😄
Sasa, do you have any tips for the construction?
24 December 2022, 11:23
Sasa Jelic
@eric, yes few of them 😄, there are good build topics on arc forums and LSP forum that cover most. The only thing I found very useful is colle21 magic dust instead of putty for all joints specially wings to fuselage and joining fuselage parts. Trim the wings as much as you can to get good fit, you will lose your nerves there but you can get almost perfect fit with good trim, so wings are problem not fuselage. Other than that it is more or less good fit and no issues. Print lines on cockpit are terrible, in the end I didn't bother to remove all of them since you would have to remove all details inside. Masks are very good fit and are better option than decals. Also I used Eduard rockets since one from kit are hard to make to look good.
@eric, yes few of them 😄, there are good build topics on arc forums and LSP forum that cover most. The only thing I found very useful is colle21 magic dust instead of putty for all joints specially wings to fuselage and joining fuselage parts. Trim the wings as much as you can to get good fit, you will lose your nerves there but you can get almost perfect fit with good trim, so wings are problem not fuselage. Other than that it is more or less good fit and no issues. Print lines on cockpit are terrible, in the end I didn't bother to remove all of them since you would have to remove all details inside. Masks are very good fit and are better option than decals. Also I used Eduard rockets since one from kit are hard to make to look good.
24 December 2022, 18:49
Treehugger
I have this kit as well with some Eduard resin missiles. I put the 1:32 Eduard missiles together, but I was disappointed by how the many fin parts on the "sparrow" wasn't nicely fitting in the sockets, but eventually I managed to glue the fins on with cyanoacrylate gule.
Nice to see people putting this one together I am a bit slow on my build. Struggling a little with the two big intakes on the inside.
A trick to deal with the stepped resin in places, is adding diluted Vallejo putty, let it dry, then gently sand flush. Obviously this doesn't work well for corners and details, just the larger surfaces.
I have this kit as well with some Eduard resin missiles. I put the 1:32 Eduard missiles together, but I was disappointed by how the many fin parts on the "sparrow" wasn't nicely fitting in the sockets, but eventually I managed to glue the fins on with cyanoacrylate gule.
Nice to see people putting this one together I am a bit slow on my build. Struggling a little with the two big intakes on the inside.
A trick to deal with the stepped resin in places, is adding diluted Vallejo putty, let it dry, then gently sand flush. Obviously this doesn't work well for corners and details, just the larger surfaces.
24 December 2022, 20:30
Album info
Jetmads 1/32 resin kit combined with DN masks for camo and markings