[Revell] BMW 507 - WIP

1
April 20, 2024
This kit was a combined set with i8, but I made i8. so this 507 was state without a box.
And, this is an old kit from a very old mold.
2
April 20, 2024
This sprue was bent when I first received it.
This is very common with revell kits.
3
April 20, 2024
I would turn it over, put something heavy on both sides, and blow air with a hair dryer every time I went back and forth for a few days.
4
April 20, 2024
It has been restored.
5
April 20, 2024
Washed.
6
April 20, 2024
Engraving panel-line and removing parting line.
7
April 20, 2024
I scraped the inside of the fender because the cross section was too thick.
8
April 20, 2024
L: original / R: scraped
9
April 21, 2024
The emblem was embossed, but I removed it because I didn't need it.
10
April 21, 2024
The part with the mold lines was thick, so I scraped it off and thinned it out. (Arrow is before fix, right is after fix)
11
April 21, 2024
Since the jaws were separate, I glued them and applied putty.
12
April 21, 2024
While the putty was hardening, I pre-assembled the bonnet and found that there was a large gap.
13
April 21, 2024
Slice the pla-plate to...
14
April 21, 2024
Glue it down and...
15
April 21, 2024
Removed gaps with sanding.
16
April 21, 2024
The putty had finished drying, so I sanded it down.
I'll have to check it again later after I paint the surfacer.
17
April 21, 2024
I have now sanded the entire body-shell.
18
April 22, 2024
The quality of the plated parts in this kit is so poor that I will have to look at them one by one and come up with a work plan.
It is the most noticeable decorative part, but it is bent and completely crushed, so it cannot be used as is.
19
April 22, 2024
The parting line is clearly visible on the bumper.
20
April 22, 2024
The grill on the front should go into the housing, but it doesn't...
21
April 22, 2024
I don't know if the room mirror part on the left is an injection defect or the mold is damaged, but it is completely unusable. The side mirror in the photo on the right also has protruding parting-line and push pin marks.
22
April 22, 2024
The vent parts near the windshield also protrude significantly rather than going inward.
23
April 22, 2024
Since the outside diameter of the headlamp housing is larger than the body, this also needs to be corrected.
24
April 22, 2024
Of the plated parts, only the side slits fit perfectly with the bodywork, so I think I can just chrome them without modification (but I'll have to remove the embossed BMW emblem).
25
April 22, 2024
For the bonnet decoration, one sheet of aluminum plate was cut into a V shape, another sheet was cut thinly, bent, and then glued together.
This is my first time doing metal processing. I don't know if it was because the aluminum was too thin, but it was difficult to process because it bent easily.
26
April 22, 2024
I put it on the bonnet and it looks allight.
27
April 22, 2024
The vertical bar was made by grinding aluminum rod into a square pillar.
I didn't have any tools or materials for metal processing, but I had some sculptural aluminium wire, so I used it.
28
April 22, 2024
I roughly carved it into a similar shape and placed it on the bonnet.
29
April 22, 2024
I trimmed it a bit more and assembled it with the wings.
I think it looks much better than the original parts.
30
April 22, 2024
The top part was shaved off a bit more and then polished to finish it off.
31
April 24, 2024
The outer diameter of the headlamp cup was narrowed by sanding.
32
April 24, 2024
The curves of the body were not smooth and showed slightly angled areas, so I sanded the entire body again.
33
April 24, 2024
The windshield parts were of poor quality, so I sanded them and then scrubbed them endlessly with a compound.
34
April 24, 2024
Done.
35
April 24, 2024
The plating was removed by soaking in bleach.
As expected, the primer was not removed. 🙁
36
April 24, 2024
As expected, the hubcaps also had primer clumped together.
I sanded it all down and removed the embossed emblem in the center.
37
April 24, 2024
I broke it while scraping the backing to make the vent area near the windshield as thin as possible.
38
April 24, 2024
Even though I scraped it off thinly, it did not go into the body.
So I drilled a hole in the body and it fit perfectly.
39
April 24, 2024
The molded mesh expression was removed and nylon mesh was attached.
40
April 24, 2024
Done.
Because the body is pierced, it fits well without sticking out even though mesh is added underneath.
41
April 25, 2024
I sigh just looking at it. 🙁
The rearview mirror in particular is in the worst shape.
42
April 25, 2024
I decided to build it up one by one, starting with what seemed the simplest.
It is a part that is inserted into the indicated location, but I do not know what it is actually used for.
Parking brake? Bonnet open handle? Anyway...
43
April 25, 2024
I cut a small piece of aluminum, trimmed it, drilled holes, assembled it with insect pin.
44
April 25, 2024
Next, I cut the neck of the side mirror and made the body by cutting and attaching thin stainless steel pipes and insect pins to the appropriate length.
45
April 25, 2024
For the mirror part, Zaku's monoeye and gun scope modification parts from Gunpla were used.
46
April 26, 2024
The muffler end was made by cutting aluminum pipe.
47
April 26, 2024
There is something made of metal on the marked part of the steering wheel, but I don't know what it is. (Maybe paddle shift?)
Anyway, I cut the aluminum into small pieces and processed it.
It was too inconvenient to work with metal, so I bought a mini vise.
So far, it seems to be quite usable.
48
April 26, 2024
It was finished by processing it into an appropriate shape, filing and polishing it, and then bending it.
49
April 26, 2024
The turn signal switch is very simple to modify.
I put a little UV resin on the end and hardened it.
50
April 27, 2024
Carving the gearstick head itself wasn't difficult, but it was so small and the plastic was bent that I had to carve it several times.
51
April 28, 2024
Next, it's time to modify the poor quality rearview mirror, which is embarrassing to even call a part.
After cutting and polishing the aluminum rod, I cut and attached a stainless steel pipe to the back.
52
April 29, 2024
The pillar part of the rear-view mirror was also made by carving aluminum rods.
There should be a bezel around the edge of the mirror, but I didn't want to bother, so I left it out.
53
April 29, 2024
I usually don't fix the pushpin marks, but since the sun visor is still very visible when finished, I had to fix it.
And while I'm at it, spreaded it to the bonnet.
54
April 29, 2024
Done.
55
April 30, 2024
Next is seats.
First, a small groove was dug at the bottom of the sheet.
56
April 30, 2024
I took a picture because there was an injection defect.
I think the mold may have been damaged.
57
April 30, 2024
I tried to express wrinkles easily.
Rough carving marks can be smoothed by wiping them a few times with non-resin adhesive (Quick Type x).
58
May 1, 2024
I replaced the seat hinges with metal.
Of course, I didn't replace the inconspicuous part on the door side.
59
May 1, 2024
Next, I carved a piece of plastic rod to make a seat position adjustment lever.
It's a little big, but let's let it go. 😉
60
May 1, 2024
The sheet is made of two pieces, front and back, but the step was quite large, so I filled it with putty.
61
May 1, 2024
I scraped it off with a knife, but the putty didn't stick and came off.
62
May 1, 2024
I quickly gave up and applied a thick layer of slightly viscous instant adhesive.
63
May 2, 2024
After sanding, I also scraped off the molds on the edges.
64
May 2, 2024
And then cut the pla-plate into thin slices...
65
May 2, 2024
I made edge line on the back.
66
May 2, 2024
Next is the sunshade.
The basic structure was created by bending thin stainless wire and cutting pieces of aluminum plate.
67
May 2, 2024
I had to make a support that would be fixed to the window frame, so I carved an aluminum rod.
68
May 2, 2024
I needed 4 pieces, so I tried to cut it into 4 pieces and screwed it up. 😄
69
May 2, 2024
Threw it... and I just cut a square pla-rod and made it.
It can't be assembled right now, but once it's painted and assembled, it will roughly look like this.
70
May 3, 2024
This is lever of side window.
It is inconvenient to work with lathe because the rotary tool I have is a bit wobbly.
71
May 3, 2024
And another lever (maybe.. door knob?)
Hmm... I think this would have been fine just by trimming the original parts.
Mine was a little too thick, so I'll have to sand it down later to make it a little thinner.
72
May 4, 2024
I wondered if the front grill part didn't fit well due to the thickness of the plating, but it didn't fit well regardless of that.
73
May 4, 2024
I had to carve out the entire inside of the part, but especially the marked area(towards the headlamp).
74
May 4, 2024
Now it's a good fit.
75
May 4, 2024
Next, I made a jig like this.
76
May 4, 2024
On the jig, thinly sliced pla-plate were attached vertically, and thin wires were cut and attached horizontally on top of them.
77
May 4, 2024
I made another one on the other side in the same way, paying attention to the direction.
78
May 4, 2024
I scraped the back of the original piece to make it as thin as possible, cut out the inside with a knife, and attached the mesh I had made.
79
May 4, 2024
Finally, cut off the protruding mesh and... Voilà!
It would have been nice to have grid etching like the detail-up parts on the Tamiya Aston Martin DBS, but since it's not there, we'll have to settle for this... 😉
80
May 5, 2024
I tried to remove the embossed BMW emblem on the side slit, but the back was so thin that it pierce through.
So I completely drilled it all down.
81
May 5, 2024
Aluminum rods were cut to an appropriate thickness and inserted.
82
May 6, 2024
It's a very old mold, so the instrument panel is embossed, but the repackaged product include the decal too.
So I removed them for the detail-up.
83
May 7, 2024
By polishing aluminum pipes of two diameters...
84
May 7, 2024
I made a chrome trim for the instrument panel.
85
May 8, 2024
A few buttons were also removed.
86
May 8, 2024
I carved a pla-rod to make a white button and placed it.
87
May 9, 2024
I also made buttons on the left side.
88
May 9, 2024
In the photo of the real car, there is a seam at the top of the dashboard, so I made a roughly similar.
The marked is where broke when the gluing.
89
May 9, 2024
I tried to use an PE wiper, but it was impossible because it was almost double size.
So I decided to just trim the original parts as thin and sharp as possible and use them. (Arrow: modified)
90
May 11, 2024
I don't know what the original shape was, but I made a new one that like an antenna.
91
May 11, 2024
It's probably the antenna, right? 🙂
92
May 11, 2024
I trimmed the aluminum rod to make a washer fluid nozzle.
The nozzle looks unusual, but I guess that's because it's a classic car. (Obviously, I omitted the nozzle hole.)

With this, it seems like the basic work for important detailing has been completed.
93
May 16, 2024
Now I was trying to trim the remaining parts, but I saw an error on the first page of the assembly instructions.
What I was holding was part number 6 in the manual, but it didn't fit because of the protrusion on the marked part.
Summary: You just need to swap parts numbers 6 and 7.
94
May 16, 2024
And I remembered that older kits have bonnets that are less closed due to engine room parts, so I tried assembling it.
Just looking at it, it looks like it won't close because of the marked parts.
95
May 16, 2024
As expected...
96
May 17, 2024
I had to cut it by the amount shown.
97
May 17, 2024
Now it's a good fit.
98
May 17, 2024
When I opened the bonnet, it seemed to open a lot, so I corrected the push pin marks.
99
May 17, 2024
Although the rivet representation on the roof cover is quite good, I decided to remove it to improve the detail.
100
May 17, 2024
I removed the rivet and marked its location with a stylus, but the plastic was so soft that it fell apart.
After applying non-resin adhesive to make it soft, I carefully restored it.
101
May 17, 2024
I trimmed all the parts and sorted them by color to be painted. Because the injection quality was not good, it took two days to refine it.
102
May 17, 2024
I painted various colors first...
103
May 17, 2024
All parts that needed to be painted glossy black were first painted with black surfacer.
104
May 18, 2024
I painted gloss black. (Wheels is over coated clear smoke on the metal black)
105
May 18, 2024
Clear over coated.
106
May 19, 2024
Again x2
107
May 20, 2024
White surfacer.
108
May 20, 2024
I sprayed a semi-gloss red to make it look almost matt.
The windshield frames shown are red on the back.
109
May 20, 2024
Since the wheel edges are chrome, I masked them.
110
May 20, 2024
It's been a while since I painted it with chrome, but it didn't turn out the quality I wanted.
Still, it's hazy now, but once it's completely dried, the reflection will be much better than it is now.
111
May 21, 2024
The under plate was also masked for painting.
The marked area has a complex shape, so I plan to paint it with a brush.
112
May 21, 2024
Finished brushing.
113
May 21, 2024
Ready to assemble. (but, I haven't polished the body shell yet)
114
May 24, 2024
Polishing Start - Sand.
115
May 24, 2024
Polishing 1. Rough compound.
116
May 24, 2024
Polishing 2. Medium compound.
117
May 24, 2024
Polishing 3. Finish compound.
118
May 24, 2024
Polishing Final - Extra finish(GSI ceramic compound)
119
May 24, 2024
I decided to work on the dashboard first, as it looked like it would require a lot of work before I could assemble it a`ccording to the assembly instructions.
I trimmed the pla-plate so that it would fit comfortably inside the aluminum housing of the instrument panel. (If it was too thin, it would tilt when inserted, so 0.5mm thick was about right.)
120
May 24, 2024
The small instrument panel was made easy to fit by adding a pla-rod to the back.
121
May 24, 2024
Then I applied decal.
122
May 24, 2024
And now I need something like this.
This is the inner packaging material for kim(seaweed), a traditional Korean food.
Anything flat, stiff, thin, and transparent will do, but this was all I had on hand.

Gossip: The global popularity of kimbap has led to an explosion in South Korea's kim(seaweed) exports, which has driven up the price of kim(seaweed) here. 🙁
Koreans can't live without kim(seaweed), kimchi, and ramyun. 🙂
123
May 24, 2024
Anyway, Cut and trimmed the PETs to the same size. (required x2)
124
May 25, 2024
Drops of UV resin were placed on the decal, covered with cut PET, pressed lightly, and then cured.
125
May 25, 2024
The aluminum pipe was fixed with wood glue at an appropriate depth.
126
May 25, 2024
Attached to the dashboard.
127
May 25, 2024
I lost some of the buttons I made, so I made them again and attached them.
While editing the photo, I found that the audio decal position was a little off. It was already fully glued so there was no way to move it sideways.
It's okay if you see it with the naked eye or from above, you won't notice it at all. Because I did that... 😉
128
May 25, 2024
A handle for some unknown purpose was also attached.
Since the handle was placed vertically, I later rotated it horizontally.
129
May 26, 2024
It was inconvenient to work if the wire moved, so I temporarily fixed it with tape and then attached it.
However, the instant adhesive flowed into the gaps, making it impossible to move.
130
May 27, 2024
Assembled the inside of the door.
131
May 27, 2024
These are metal stickers that I personally made last year for things I thought would be needed in the kits I own.
motorart.tistory.com/605
motorart.tistory.com/394
However, because I did a lot of modifications this time, I ended up using only the one shown.
132
May 27, 2024
Why I love metal stickers.
133
May 27, 2024
Next, Using etching and insect pins...
134
May 27, 2024
I made the pins for the roof cover.
I planned to do it as marked, but making one of those was extremely stressful because the head of the insect pin would stick out, fall off, or not stick in place.
I gave up because I wasn't confident enough to make 11 pieces.
135
May 27, 2024
So, I just glued the etching on for now. (Well... it looks fine as is.)
136
May 28, 2024
It wasn't included in the kit, but I thought it would be nice to have a seat belt, so I decided to make one.
A piece of plastic was trimmed into an appropriate shape and attached to the end of black tape of the appropriate width with instant adhesive.
In Korea, they call it line tape, but in English it's probably called whiteboard tape.
137
May 28, 2024
Then paint to create a seat belt socket and...
138
May 28, 2024
Next, I cut the etching to create a clip.
139
May 28, 2024
And so, the seat is assembled.
140
May 28, 2024
A drop of UV resin was placed on the BMW emblem decal and hardened.
141
May 28, 2024
Assembled the wheel cover.
142
May 28, 2024
UV resin was also applied to the gear stick and hardened.
143
May 28, 2024
Since the attachment surface must be flat to attach the embossed emblem decal, the aluminum parts made in #81 could not be used. Instead, I shaved the pla-rod.
144
May 28, 2024
I attached all the remaining decals.
145
May 28, 2024
Attached F/R emblem.
146
June 1, 2024
I attached the emblem in the side slit.
147
June 1, 2024
I also attached decorations to the bonnet.
148
June 1, 2024
Assembling the windshield. It was quite a pain to attach the sun visor.
149
June 1, 2024
Engine built.
150
June 1, 2024
I'm trying to attach a radiator but there are no holes indicated in the instructions.
I had no choice but to cut off the male pin and attach it with glue.
151
June 1, 2024
Bottom parts done.
152
June 1, 2024
Interior start.
153
June 1, 2024
Interior done.
154
June 1, 2024
Another picture.
155
June 1, 2024
Steering parts were assembled.
156
June 1, 2024
Engine room parts were assembled.
157
June 1, 2024
Assembled wheels .
158
June 2, 2024
Assembled hip.
159
June 2, 2024
Attached grill.
160
June 2, 2024
Attached vent.
Because it was processed to fit perfectly, it became narrow due to the thickness of the paint, so when I forced it in, the place where it had broken once broke again.
161
June 2, 2024
Attached gills.
162
June 2, 2024
Assembled face.
163
June 2, 2024
Join to bottom.
There was a gap so large that the marked area could not be covered by the windshield.
164
June 2, 2024
When separating the upper and lower, the paint on the marked area was cracked.
So I painted over it, but it didn't come out clean. 🙁
165
June 2, 2024
In the end, I took it apart again, moved the dashboard a little forward, put the upper and lower plates together, and then installed the wheels.
166
June 2, 2024
Anyway, now I've attached all the remaining parts and it's done.
167
June 2, 2024
Yeah~
168
June 2, 2024
I also put a roof on.
169
June 2, 2024
Well, it's not bad.
170
June 2, 2024
However, since the interior was made with great care, we decided to leave it open. (Of course, it is removable, but...)
171
June 2, 2024
It's finally over!
Thanks for watching the long production period, and see you next time with the completed photos.

Commenti

82 20 April 2024, 18:29

Michael Kohl
Following

20 April 2024, 19:07

Robert Podkoński
Watching with pleasure.

21 April 2024, 06:26

Dominik Weitzer
oh wow....that looks not good with the fitting of the chrome parts.
i've build this BMW twice and had not that issues. perhaps, the mold is old :-D because i had the first issue i worked with.

good luck! At the end. it is a very nice model 😉

22 April 2024, 08:09

MS K Autore
Yah I agree Dominik, and It is also the only 507 kit. thanks 😉

22 April 2024, 08:44

Michael Kohl
As expected a treat to follow.

22 April 2024, 11:44

David Fuller
Following

22 April 2024, 20:53

István Szücs
Much work for the perfect result... Respect, Sir!

25 April 2024, 08:46

Jv
As always I think we all appreciate your step by step build pics and the problems in the kit
You find
Fantastic work on the model but also on the instructions on how you overcome
The challenges in the kits
Sure a cool car but looks to be a challenge to build
Fantastic work

25 April 2024, 09:20

Christian W
I like your detailling

25 April 2024, 10:40

Spanjaard
fantastic tutorial 🙂

25 April 2024, 11:13

Michael .
Great job so far. Love the work on the hood (bonnet) decoration. Looks great.

25 April 2024, 11:33

Bruce Huxtable
Here, here to all th eprevious comments 🙂 I'm learning lots - especially that one should not be daunted by poor quality parts!!

26 April 2024, 14:27

Alexander Grivonev
Following

29 April 2024, 09:37

Christian W
I'm wondering, how you handle those tiny tiny selfmade parts. Crazy.

29 April 2024, 10:52

Alexander Grivonev
This is some tideous work. These older kits are quite the pain in the butt sometimes but you are doing an astounding job with these improvements 👍. Following with great interest!

30 April 2024, 07:23

Treehugger
Oh. Bending and gluing on a thin strip of styrene is tricky, next to impossible if the turn/bend is too hard, as the glue will in my experience, always snap the rod.
What might work, is to glue on one end of the rod, then make the bend, and then glue on, only parts of the styrene rod, and making sure you don't use too much liquid glue, or the thin styrene rod snaps.

2 May 2024, 06:24

MS K Autore
That's right. I broke it once too. hahaha
I thought it was because my pla-plate was so old (I bought it over 15 years ago) that it was worn out.

2 May 2024, 06:39

Treehugger
It just occurred to me that cyanoacrylate glue is the key glue to use in such cases. Only now today did I think of that. I suspect the superglue won't react with the styrene, and so it won't snap I think.

Sometimes fiddling too much with thin bits of some styrene rod, if you started to bend it, makes the rod snap, same with thin plastic parts, and so I try to be gentle and not overly twist and rold the parts in my fingers.

2 May 2024, 06:48

István Szücs
Fantastic details!

2 May 2024, 08:04

Bruce Huxtable
I'm experiencing huge enjoyment seeing the tiny pieces of perfection that you are hand-crafting 🙂

3 May 2024, 13:07

Pepe
😍

3 May 2024, 14:00

Martin Oostrom
This is wonderful class in modelling. Thanks for all the lessons! 👍🏻

4 May 2024, 17:09

MS K Autore
You're welcome. thanks. 🙂

4 May 2024, 19:54

Marcelo S Camargo Pinto
Very well down details!

5 May 2024, 01:54

Dominik Weitzer
Wow (again). how did you glue the "metal"-parts like the missoros? that is outstanding detailwork!!! Im just on side 6 from your well documented build. amazing!
btw. the handle on the dashborad left is for the parkingbrake.
the two "paddles" on the steeringwheel are the hornbuttons 😉

6 May 2024, 08:09

Alexander Grivonev
Oh man you are going places with this. Amazing work...

6 May 2024, 11:01

István Szücs
You are insane!

Will there be any parts, you won't change?

8 May 2024, 15:06

Michael .
Fantastic. I'm interested how the speedo and tach are going to be mounted in those beautiful trim rings.

8 May 2024, 15:10

Bill Newcomer
Wow, your desire and ability to work with such small items is admirable.

12 May 2024, 23:26

Spanjaard
great details

13 May 2024, 06:38

Michael Kohl
I just love this build.

13 May 2024, 16:06

bughunter
Great detail work on each and every little part 👍
What kind of glue do you use for the aluminum parts?

17 May 2024, 20:45

MS K Autore
Thanks guys.
@bughunter - I used AXIA031, Loctite Easy Brush. Since cianoacrilate super glue is weak to impact, sometimes additional woodworking glue is applied. 🙂

18 May 2024, 05:22

István Szücs
It's still amazing!

20 May 2024, 11:33

bughunter
Thank you!

21 May 2024, 06:55

Jv
Fantastic work as always
An inspiration to all
I ha e a few mediocre kits in my stash of a few cars I think are cool
Thanks for sharing how we can make them butiful builds

21 May 2024, 12:13

Ben M
I appreciate all your details on how you improve things. Thank you.

24 May 2024, 11:48

István Szücs
Amazing, amazing details!

25 May 2024, 19:01

Treehugger
Lots of fun detailing. 🙂
Wonder where he got his tiny nylon mesh from. I could use some of that for a future 1:24 70's Dodge Challenger kit, a kit which.. when ordered off Amazon is shipped.. in December in 5-6 months. One can buy photo etch, but there doesn't seem to be any photo etch for venting mesh parts for the the hood on the car,, which is surprising. A nylon mesh might work nicely.

28 May 2024, 07:56

MS K Autore
@Treehugger - Japanese kits like Tamiya, Hasegawa racing car often come with nylon netting, which I save as much as possible and use for things like this.

28 May 2024, 08:16

István Szücs
The handle on the #128 picture is the handbrake, I think.

So, at the end of the build you will turn the key, and drive into the sunset?

28 May 2024, 19:19

Michael .
I didn't see him scratch build a tiny key ring with keys... That may still be on his todo list...

28 May 2024, 20:03

Christian W
Awesome outcome! With all the detailling it's sad, that if you don't know about it, it's hardly to see. It looks fantastic.

3 June 2024, 04:22

Robert Podkoński
Awesome indeed! Even more, taking into account how quick the build process was and the quality of the kit itself... Chapeau bas!

3 June 2024, 04:43

Spanjaard
superb job. it looks fresh out of the shop. it could be in the BMW catalogue 😉 thanks for all the extra info

3 June 2024, 08:20

Adam Gudynowski
Stunning job!

3 June 2024, 10:58

Michael .
Beautiful!

3 June 2024, 12:21

Alexander Grivonev
What a beautiful build, it was a pleasure to follow along, so many fantastic details👍 Amazing!

3 June 2024, 12:22

MS K Autore
Thanks everyone~ 🙂

3 June 2024, 12:33

George Williams
Gorgeous.

3 June 2024, 12:34

Michael Kohl
Absolutely

3 June 2024, 13:16

Marcel
You took a lousy kit and turned it into a work of art. Great job!

3 June 2024, 17:21

Martin Oostrom
This has been a great and inspiring build. Thank you MS K 👍

3 June 2024, 17:29

gorby
Stunning! Beautiful result.

3 June 2024, 17:29

István Szücs
Wonderful!

3 June 2024, 19:18

Dominik Weitzer
wow.

4 June 2024, 14:10

bughunter
A wonderful build log with a beautiful result 👍

4 June 2024, 15:11

J35J
Excellent work! Congrats👍🏻

4 June 2024, 16:39

István Szücs
Perfect result, congrats!

4 June 2024, 17:59

Jv
Wow another beautiful model congratulations

5 June 2024, 04:51

bughunter
What kind of clear coat do you use? I guess 2K?

12 June 2024, 09:34

MS K Autore
@bughunter - I used GSI Super Clear III UV Cut. thanks.

12 June 2024, 13:44

bughunter
Thanks for your answer! I have it in my stash (also the flat one) but have not tried to polish it.

12 June 2024, 14:05

MS K Autore
@bughunter - Gloss clear paints with UV cut effect sometimes do not cure well.
Unless you are in an environment where you will be exposed to sunlight for a long time, I recommend normal clear.

And the compound I use is as follows:
Rough: GSI Mr. Compound #600 (red label)
Medium: Tamiya Fine (blue lid)
Finish: Tamiya Finish (white lid)
Extra Finish: GSI ceramic compound

After each step of polishing, it is good to wash it thoroughly with water before proceeding to the next step polishing.
This is because any coarse compound particles left behind will get mixed up when polishing with the next finer compound, making it less effective.

I'm using a translator and I don't know if my English explanation is correct. 😉

12 June 2024, 15:39

bughunter
Thanks for the detailed explanation! The translation is understandable.

12 June 2024, 16:02

Rui S
Impec. Shiny paint Job 👍 another beauty from your bench

12 June 2024, 21:56

Album info

FHD images - motorart.tistory.com/758

[Revell] BMW 507

241 immagini

1:24

Completato

1:24 Gift-Set 100 Years BMW (Revell 05738)

Tutti gli album

Visualizza tutti gli album »