Polaris MRZR build thread
1
May 25, 2020Packaging from the shop2
May 25, 2020Inside look on the 6 zip-lock packets3
May 25, 20206 Packets inside the box4
May 25, 2020unboxing5
May 26, 2020most fragile packet with foam wrapped on these 3 parts
Packet A
front bumper rail
rear bumper rail
rear tow hitch6
May 26, 2020Packet B
Rollover side bars
Side handle railing
Rollover cross bar
Rear tray railings7
May 26, 2020Packet C
Steering columns
Hitch and handles (broken)
Suspension front
Torsion axial front
Torsion axial rear8
May 26, 2020Packet D
4 x tire/wheels
Side steps
Tail gate
Rollover front bar9
May 26, 2020Packet E
Chassis Front
2 x seats10
May 26, 2020Packet F
Chassis Rear
Exhaust
Chassis bottom frame11
May 26, 2020Broken part on the tail gate frame brackets12
May 26, 2020Frame dimension is smaller than the chassis13
May 26, 2020poor alignment between the guidepins 🙁14
May 28, 2020Wash and dry from resin kit parts15
May 29, 2020Different exhaust design between C2 n MRZR, length longer on the C216
May 28, 2020Comparing the size between the C2 and MRZR17
May 29, 2020Filing and prep for front and rear chassis18
May 29, 2020Dry fitting after filing19
May 29, 2020Axial is turned, to the right
Updated: turned to the same direction20
May 30, 2020Parts for axials, suspension, chassis frames and exhaust21
May 30, 2020Front axial with suspension22
May 30, 2020Rear axial23
May 30, 2020Angled to the forward on the front axial. The wheels are aligned straight at this angle.
This is correct?24
May 30, 2020Chassis frame front25
May 30, 2020Chassis frame rear in 2 pieces26
May 30, 2020Easier to fix these axials first before joining the front and rear chassis27
May 30, 2020Dry fitting on the axial chassis steps28
June 1, 202029
June 1, 202030
June 1, 202031
June 1, 202032
June 1, 202033
June 1, 202034
June 1, 202035
June 1, 202036
June 1, 202037
June 1, 202038
June 1, 202039
June 1, 202040
June 1, 202041
June 1, 202042
June 1, 202043
June 1, 202044
June 1, 202045
June 1, 202046
June 1, 202047
June 1, 2020Dry fit on rear bumper and tow hitch48
June 1, 202049
June 1, 202050
June 1, 202051
July 17, 202052
July 17, 202053
July 17, 202054
July 17, 202055
July 17, 202056
July 17, 202057
July 17, 2020Assembly on rear axial58
July 17, 2020Assembly on front axial59
July 17, 2020Assembly on front axial, left side is too high60
July 17, 2020Extending tow hitch hole using 0.8mm drill bit61
July 17, 2020Tow hitch is still too tight after drilling with 1mm drill bit62
July 17, 2020Extending tow hitch hole using 1.5mm drill bit63
July 17, 2020Dry fit tow hitch after extending to diameter 1.5mm (bottom view)64
July 17, 2020Dry fit tow hitch after extending to diameter 1.5mm65
July 17, 2020Dry fit tow hitch after extending to diameter 1.5mm66
July 17, 2020Shortening rear bumper rod for tighter fit with chassis67
July 17, 2020Rear bumper and tow hitch assembly (bottom view)68
July 17, 2020Rear bumper and tow hitch assembly (right view)69
July 17, 2020Rear bumper and tow hitch assembly (rear view)70
July 19, 2020Fitted the side steps (top view)71
July 19, 2020Fitted the side steps (bottom view). A little scrappy on the fittings :-/72
July 21, 202073
July 21, 202074
July 21, 202075
July 21, 202076
July 21, 202077
July 21, 202078
July 21, 202079
July 21, 202080
July 21, 202081
July 21, 202082
July 21, 202083
July 21, 202084
July 22, 2020Most frustrating the lug broke again while installing the tailgate. Now back to reworking the lugs again!!??85
July 22, 2020Finally managed to break all the tailgate lugs 🙁 🙁 🙁86
July 22, 202087
July 22, 202088
July 23, 2020Broke again! Good thing all the lugs break clean :-/ now I’m quite good at fixing this micro parts89
July 24, 202090
July 24, 202091
July 24, 202092
July 25, 20203 completed without their rollbar93
July 26, 202094
July 26, 202095
July 26, 202096
July 26, 202097
July 26, 202098
July 26, 202099
July 26, 2020100
July 26, 2020101
July 26, 2020102
July 26, 2020103
July 26, 2020104
July 29, 2020105
July 29, 2020
コメント
2 April 2025, 01:21 -