My grail
![Album image #1 Album image #1](/albums/img/0/6/8/1459068-18207-43-720.jpg)
![Album image #2 Album image #2](/albums/img/0/6/9/1459069-18207-48-720.jpg)
Masking done
![Album image #3 Album image #3](/albums/img/0/8/0/1460080-18207-55-720.jpg)
Happy with the rear
![Album image #4 Album image #4](/albums/img/0/8/1/1460081-18207-90-720.jpg)
![Album image #5 Album image #5](/albums/img/0/8/2/1460082-18207-94-720.jpg)
Bit of bleed in front of the windscreen. Touch up or remove the stripes from this bit?
![Album image #6 Album image #6](/albums/img/0/8/5/1460085-18207-89-720.jpg)
Happy with the masking on the side stripes
![Album image #7 Album image #7](/albums/img/0/8/3/1460083-18207-57-720.jpg)
![Album image #8 Album image #8](/albums/img/0/8/4/1460084-18207-44-720.jpg)
Went with a blue grey after being unhappy with my oranges and yellows. Wasn’t going to risk it
![Album image #9 Album image #9](/albums/img/0/5/8/1463058-18207-92-720.jpg)
![Album image #10 Album image #10](/albums/img/0/5/9/1463059-18207-28-720.jpg)
![Album image #11 Album image #11](/albums/img/0/6/0/1463060-18207-41-720.jpg)
![Album image #12 Album image #12](/albums/img/0/6/1/1463061-18207-45-720.jpg)
Added a vinyl roof from masking tape
![Album image #13 Album image #13](/albums/img/7/8/8/1465788-18207-14-720.jpg)
Tools for the vinyl roof. A steel rule, sharp knife and some black masking tape
![Album image #14 Album image #14](/albums/img/7/7/9/1465779-18207-44-720.png)
This is the masking tape I used. I am sure there are others that will work as well
![Album image #15 Album image #15](/albums/img/7/8/6/1465786-18207-31-720.jpg)
It already has a nice texture to it
![Album image #16 Album image #16](/albums/img/7/8/3/1465783-18207-78-720.jpg)
I needed to make it a little narrower hence the rule. Then place it centrally on the roof with overlap on front and back
![Album image #17 Album image #17](/albums/img/7/8/2/1465782-18207-30-720.jpg)
Using a blunt tool press the edges into the ridges that define the windows / chrome trim. Then using that as a guide cut off the excess
![Album image #18 Album image #18](/albums/img/7/8/4/1465784-18207-42-720.jpg)
When trimmed you get the centre piece done
![Album image #19 Album image #19](/albums/img/7/8/5/1465785-18207-97-720.jpg)
Add one of the sides. The overlap represents what is seen on the original. Keep this uniform
![Album image #20 Album image #20](/albums/img/7/8/7/1465787-18207-95-720.jpg)
Add some cuts to make it easier to make the tape confirm to the curves
![Album image #21 Album image #21](/albums/img/7/8/0/1465780-18207-21-720.jpg)
Then press in and cut as per the centre section. I didn’t follow the correct line on the rear pillar.
![Album image #22 Album image #22](/albums/img/7/8/1/1465781-18207-63-720.jpg)
It should have been nearer the glass.
I have removed the tape and would start again
I have removed the tape and would start again
![Album image #23 Album image #23](/albums/img/8/2/8/1465828-18207-89-720.jpg)
![Album image #24 Album image #24](/albums/img/8/2/9/1465829-18207-35-720.jpg)
![Album image #25 Album image #25](/albums/img/9/7/3/1465973-18207-50-720.jpg)
![Album image #26 Album image #26](/albums/img/9/7/4/1465974-18207-60-720.jpg)
Finished
![Album image #27 Album image #27](/albums/img/9/7/5/1465975-18207-68-720.jpg)
![Album image #28 Album image #28](/albums/img/9/7/6/1465976-18207-35-720.jpg)
![Album image #29 Album image #29](/albums/img/9/7/7/1465977-18207-67-720.jpg)
![Album image #30 Album image #30](/albums/img/9/7/8/1465978-18207-36-720.jpg)
![Album image #31 Album image #31](/albums/img/9/7/9/1465979-18207-34-720.jpg)
![Album image #32 Album image #32](/albums/img/9/8/0/1465980-18207-91-720.jpg)
Komentarzy
10 July 2024, 11:12 -