[Fujimi] 1/24 Lamborghini Veneno - Job Log

1
January 22, 2022
Attach and remove seamline. but it was my mistaken.
This part should be painted matt black.
2
January 22, 2022
I would not use wings.
3
January 22, 2022
This part has a eject pin mark on the inside.
4
January 22, 2022
I'm not going to use the wings, but I still put a drop of cyanoacrylate(loctite) to get rid of the eject pin marks.
5
January 22, 2022
Water washing with mild detergent.
6
January 22, 2022
I painted the inside black to block light penetration.
7
January 22, 2022
However, it is impossible to paint inside these places.
8
January 22, 2022
So that part had to be painted on the outside as well.
9
January 22, 2022
I wiped the part that was too dirty.
10
January 22, 2022
Masking...
11
January 22, 2022
I paint, Momodeling gloss white surfacer.
12
January 22, 2022
Masking...
13
January 22, 2022
I use try colors.
R: GSI shine red.
Y: IPP orange yellow.
B: Turquoise. (custom made)
14
January 22, 2022
Hint: Fluorescent yellow is required.
15
January 22, 2022
Matt clear coat on the Red.
16
January 22, 2022
Mask again and painting metal gray.
17
January 22, 2022
Gloss clear coat.
18
January 22, 2022
Polishing and Compoundin
19
January 22, 2022
It was not pre-cut.
20
January 22, 2022
Painting matt black.
21
January 22, 2022
Painting carbon pettern with stocking on the painted semi gloss black.
22
January 22, 2022
Brush painting and use panel line accent.
23
January 22, 2022
Decal applied.
24
January 22, 2022
Ready to assemble.
25
January 22, 2022
1st, assemble the wheels.
26
January 22, 2022
Since the lower plate was curved, I checked the floating part by putting the wheels on it. (No problem)
27
January 22, 2022
Engine built.
28
January 22, 2022
Assemble interior.
29
January 22, 2022
The wipers may come off when assembling the windshield, so I glued them in beforehand.
The marked part will float when the windshield is combined with the body shell, so it is better to attach it beforehand.
30
January 22, 2022
The crosshairs pin in the manual did not actually exist.
31
January 22, 2022
The marked part does not adhere.
32
January 22, 2022
In the meantime, the adhesive adhered to the body surface.
After it was completely dried, it was polished with sandpaper and compounded.
33
January 22, 2022
It turned out that the marked part was the attaching point.
It would have been nice if it was well explained in the manual.
However, nevertheless, it does not fully adhere to the A-pillar.
34
January 22, 2022
This is aurora beads.
35
January 22, 2022
As a mirror surface, a metal sticker was cut and used.
36
January 22, 2022
The left tail lamp that was attached from the inside fell off.

Since the body shell and the lower plate are firmly attached, it is impossible to recover.
However, at first, it took me a long time to figure out which part was missing, so I deliberately showed it to the people around me without explaining it, and they were not conscious of it at all.
37
January 22, 2022
This x-shaped strut bar can only be attached at this stage.
38
January 22, 2022
Opened door and cowl.
But I always finish with the door closed.
39
January 22, 2022
Finish
40
January 22, 2022
Finish
41
January 22, 2022
Finish

Comentarii

12 22 January 2022, 13:57

Scott S
Nice to see one of these kits built. Thanks for adding captions on some of the problem areas, it helps people know what to look out for. Nice customization. Too bad about the tail light, maybe you could get a spare part from Fujimi and somehow insert it from the outside into place.

22 January 2022, 19:59

MS K
Thanks Scott.
It is a structure that cannot be inserted from outside by design.
I just decided not to care. ಥ﹏ಥ

23 January 2022, 06:30

Tom ...
Another excellent build. Very impressed with the carbon fiber technique. I imagine it is very hard to get it to look right...

1 February 2022, 11:59

Michael Kohl
talking about carbon fiber technique. Can you elaborate a bit more, as I have no idea of how you actually did it. Particularly interesting have been for me your problems and how you solved them.

1 February 2022, 15:21

MS K
Thanks Tom 🙂

@Michael Kohl
It is classical technic.
1. The surface should be moderately smooth.
2. Paint it black(not 'Matt') and dry. If you want 'Kevlar', than use another color (like 'Lignt Brown')
3. On top of that, place stockings on it and make it adhere to the curved surface. (attention should also be paid to the direction of the pattern)
4. Now lightly airbrushing 'GunMetal or Light GunMetal' over it.

You will probably need some practice. 😉

1 February 2022, 21:02

Michael Kohl
Thanx MS K for explaining. Not being a car modeler I have not been familiar with this technique.

2 February 2022, 08:57

Album info

motorart.tistory.com/397

Lamborghini Veneno (Custom Color)

108 imagini

1:24

terminat

Toate albumele

Vizualizați toate albumele »