[Tamiya] Ford Mustang GT4 (Job Log)

1
March 6, 2022
I stabbed my finger and it hurts. It is very sharp, so be careful.
2
March 6, 2022
Don't cut.
3
March 6, 2022
I will remove this mold.
4
March 6, 2022
Trimming and washing.
5
March 6, 2022
I painted inside to black for anti subsurface scattering.
6
March 6, 2022
L: Fluorescent yellow.
R: Overcoated in a light yellow.
7
March 6, 2022
Done.
8
March 6, 2022
L: Need cut off.
R: Carbon pattern not printed properly.
9
March 6, 2022
I drew a vector logo to try out a laser engraver.
10
March 6, 2022
I put masking tape on the PET and cut it.
11
March 6, 2022
1st: Stick to outside.
2nd: Stick to inside.
3rd: Remove outside.
12
March 6, 2022
And, I paint with a black and carbon pattern.
13
March 6, 2022
Then I remove it.
But, the edge was not clean.
14
March 6, 2022
Hahaha I'm going to erase everything and use the decals.
15
March 13, 2022
White surfacer (Gloss).
16
March 13, 2022
Gloss clear coated (once)
17
March 13, 2022
L: Momodeling fluorescence yellow (I use this)
R: IPP fluorescence yellow
Maybe I think 'L' is not pigment type.
18
March 13, 2022
Print miss. So I didn't use the little decals.
19
March 13, 2022
Decaling done.
20
March 13, 2022
Various base colors were painted on the small parts.
21
March 13, 2022
'Gloss Black' and 'Gloss Clear' coat.
22
March 13, 2022
Gloss clear coated. (once)
23
March 13, 2022
Compounding done. But paint has been erased.
24
March 13, 2022
Tamiya Pannel Line Accent.
25
March 13, 2022
Problems occurred when removing the tape after masking and painting only the erased areas.
26
March 13, 2022
Heavy trouble....
27
March 13, 2022
When I carefully removed the decal film, the film was intact and only the ink was attached to the masking tape.
28
March 13, 2022
Inevitably, I have to make letters with stencils.
29
March 13, 2022
This time, I masked the decal as carefully as possible so that it doesn't fall off again.
30
March 13, 2022
I think the result is quite satisfactory.
31
March 13, 2022
Gloss coated and polished(rough).
32
March 16, 2022
Masking...
33
March 16, 2022
Done.
34
March 16, 2022
Black surfacer.
35
March 16, 2022
Carbon pattern using stockings.
36
March 16, 2022
Partial painting with a brush.
37
March 16, 2022
I was worried that the decal would come off again if I masked it, so I painted the window frame with a brush.
38
March 16, 2022
Ready to assemble.
39
March 16, 2022
The interior decals are from Tamiya.
40
March 16, 2022
I used a silver foil sticker from GunPla.
41
March 16, 2022
Assembling the lower part
42
March 16, 2022
Tires and windshield. (Indycals)
43
March 16, 2022
Pre-assemble.
44
March 16, 2022
Interior done.
45
March 16, 2022
Interior done.
46
March 16, 2022
Interior done.
47
March 16, 2022
I missed.
Painted with 'Vallejo Mecha Black Primer'.
48
March 16, 2022
Assemble, Re
49
March 16, 2022
Assemble, Rear
50
March 16, 2022
Assemble, Front.
51
March 16, 2022
Assemble, Front.
52
March 16, 2022
I used Hasegawa 'White Finish' for the inside of the headlamps, which should be painted white.
53
March 16, 2022
I cut the metal sticker included with the Tamiya case and apply mirror.
54
March 16, 2022
Attach everything that needs to be attached inside the shell...
55
March 16, 2022
And after joining the upper and lower plates, I attached the under cowl.
56
March 16, 2022
Finally, attach the rest of the exterior parts and done.
57
March 16, 2022
Finish~

Коментари

10 6 March 2022, 14:47

Jv
Got the same one interested in your build
And thanks for the heads up
Taking a seat

6 March 2022, 15:37

Jv
Year na mate not sure what you did whed the finger
But I guss you worked out that's not how to do it

6 March 2022, 15:40

Jv
I found that the tamiya tape did not give me a clean edge
Paint bleads under it I am going to try frog tape

13 March 2022, 16:08

MS K
Maybe i think, I am concerned that the adhesive force will not be strong for use in models.
If the masking tape is old, or if dust adheres to the side during storage, the edges will be not clean.
If the surface to be masked is flat and uncomplicated, I recommend masking film.

13 March 2022, 16:33

Jv
I bugth some tamiya tape and used it a few days later and found bleading paint
I have used frogtape before
not on models
But to me it looks like its better
So I will give it a go
It you use frogtape you need to rub the tape on hard
It dosent stick like Tamiya does
But I will let you know how I go

13 March 2022, 16:41

John Hughes
I've found Tamiya tape can be a bit hit & miss around the edges. I thought it was just me doing it wrong!

13 March 2022, 16:56

Jv
Always interesting to hear what experiences others have
And I think in this build ms k has had some of the problems I have seen for myself
And I know the tape was very new
I also noticed the problem whed bleeding in other people's builds
Specaly on taping up clears
And also noticed it on people masking up for stripes
So I think its more miss then hit lol

13 March 2022, 17:08

Robin (WhiteGlint)
Very nice save 👍

13 March 2022, 17:27

MS K
Thanks WhiteGlint.
O.K. Jv. I'll wait for your review.
I'm curious too, so please let me know your Exp.

13 March 2022, 18:08

Jv
Will do bur it will be a few weeks before I will mask anything up agen I am not happ whed my paint results at the moment
And will upgrade my paints
And go airbrush in hope of better results
Sofare I have just used cans from the hardware store
And can't get a good result whed them

13 March 2022, 18:16

Martin Oostrom
It looks like the tape took the clear and the ink with it... Most unusual and a shame as the build was really looking good so far. Please save her!

16 March 2022, 16:06