Citroën Mehari Heller 1/24

1
November 4, 2016
Kit box
2
November 4, 2016
Box contents
3
November 4, 2016
Sprues
4
November 4, 2016
Sprues
5
November 4, 2016
Sprues
6
November 4, 2016
Sprues
7
November 4, 2016
Let's start with the engine block and suspension arms.
8
November 4, 2016
Chassis pan
9
November 4, 2016
Workbench
10
November 4, 2016
Cylinders need some putty
11
November 4, 2016
Some green putty ...
12
November 4, 2016
A bit of detail has been added to the engine
13
November 8, 2016
Some stretched sprue strakes added to the sump
14
November 8, 2016
Cylinders and carb glued to the block
15
November 8, 2016
Also disk brakes haven been glued
16
November 8, 2016
Suspension arms glued to the chassis pan. The joint is too weak and I had to reinforce it with with CA glue.
17
November 27, 2016
Admission ducts and front fan added
18
November 27, 2016
Engine
19
November 27, 2016
Engine
20
November 27, 2016
Engine
21
November 27, 2016
Chassis with marked section to be removed. Sump did not fit in the opening.
22
November 27, 2016
More progress on the engine. Now with air intakes and exhausts shrouds have been glued in place.
23
November 27, 2016
Checking the mudguards and engine clearance with blue-tack. Just to check if the engine fits properly before it's too late.
24
November 27, 2016
Engine almost finished wiht air filter box glued.
25
November 27, 2016
Hand painting the recesses which will be difficult to reach with an airbrush. Tamiya X-6 gloss orange which is a perfect match to me.
26
November 27, 2016
Finished engine.
27
November 27, 2016
Finished engine with exhausts connected to the muffler.
28
January 15, 2017
Engine mated to the chassis
29
January 15, 2017
When the mufflerwas fixed in its proper place in the chassis , I couldn't connect it to the exhausts , so I replaced the "rigid" plastic parts with vinyl tubing.
30
April 26, 2021
Some sink marks to be dealed
31
April 26, 2021
Checking chassis and body fit.
32
April 26, 2021
Done ... heating hoses were added from vinyl tube (white).
33
April 26, 2021
Brake pump "tank" made from a plastic tube and a styrene disc.
34
April 26, 2021
35
April 26, 2021
ARRRGGGG .... front disk lines added ... which now (April 2021) working on a 2CV pic-up found that this is not correct . The engine has inboard disk brakes , which is quite clear in picture 29.
🙁😭(((
36
April 26, 2021
Completed fuel pump plus tubing. Also hand brake converted from a left-over part of the kit.
37
April 26, 2021
I lost one wind-screen wiper ... so I had to scratchbuilt both .... I'm quite pelased with the result
38
April 26, 2021
The kit does not include glass for the head lamps ..... Spare box came to rescue
39
April 26, 2021
Wind scrren wipers made from scratch. Look the part to me.
40
April 26, 2021
Metallic disc to cover the holes for the canvas were made with lead from a wine bottle capsule and Waldron Punch & Die Set ... colour is perfect as is .... 😉
41
April 26, 2021
Adding straps for the bonnet ,,, not very true to scale ,,, but made to allow removing of the bonnet .... and putting it back again
42
April 26, 2021
Glued 4 pins to help fixing the bonnet in place.
43
April 26, 2021
Completed engine bay. All these items were added : brake pump and lines , heating hoses , electric wiring to the head lamps and the battery , exhaust shrouds , "glass" for the head lamps
44
April 26, 2021
45
April 26, 2021
Finished in December last year ,,,, it was high time that I post the pictures.
46
April 26, 2021
47
April 26, 2021
48
April 26, 2021
49
April 26, 2021
I'm still trying to find a suitable speedometer decal
🙁😭((
50
April 26, 2021
Finished .... hummmm ,,, seeing the pictures I notice some missing items ... i.e. wheels air valves , and brake hoses for the rear wheels ,,,,,, front brakes are inboard.

Kommentarer

9 4 November 2016, 18:23

Julian Herrero aka Yuri
As soon as I saw it in the shop I knew I had to buy it .. and build it asap. In fact it didn't even went to the stash ... went from the shop right to my workbench.
The kit is rather basic in some aspects ... no fuel tank, simplistic fuel filler cap, no clear plastic for the head-lamps .... Nevertheless the engine is quite detailed, but a some tubes and connectors missing. In fact some tubes are on the sprues but not in the instructions ,,, more anon.
Beware, gates to some parts are really tiny and prone to break ... I've just lost one windshield wiper ...

6 November 2016, 17:05

Jorge Ferreira
Congratulations. Not an easy kit to deal with. If we wan`t to make it better our imagination is the limit . I did mine a few years ago and I`m still looking for the right side rear view miror.

26 April 2021, 18:44

MS K
I also made one, and I think it's a very fun kit.
The orange color seems to go very well 🙂

27 April 2021, 16:08

Julian Herrero aka Yuri
Yes ... the kit is really fun to build ... no major build troubles ... What's shocking for such a moder kit is all the parts it lacks ..... headlights glass it's just a flagrant missing

29 April 2021, 13:35

MS K
Oh, I agree. Headlights are clumsy.

29 April 2021, 17:39

Album info

Standard build, with just a few detailing and corrections. Pretty much an OOB job.
As soon as I saw it in the shop I knew I had to buy it .. and build it asap. In fact it didn't even went to the stash ... it went from the shop right to my workbench.
The kit is rather basic in some aspects , all these items are missing :
fuel tank
simplistic fuel filler cap
no clear plastic for the head-lamps
no brake pump
no heating hoses
no speedo
no handbrake lever
no ashtray
no bonnet straps
Nevertheless the engine is quite detailed, but some tubes and connectors are missing. In fact some tubes are on the sprues, which I guess are for the 2CV kit.
I added just a few things to get it right ,but not much more.
I can stand with all that.

Citroën Mehari Heller

50 bilder

1:24

Avslutad

No 0,5mm High Flow D?se (t?rkis) (Aztek A9306)

No Tamiya Extra Thin Cement (Tamiya 87038)

All albums

View all albums »