Panhard AMD 178 1/72 (RPM)

1
December 1, 2021
The boxart is rather nice and the instrutions are on the box instead of a seperate booklet/sheet.
2
December 1, 2021
Only two sprues should point towards an easy assembly... shouldn´t they?
3
December 1, 2021
Wheels are not Takom quality of details, but are good enough and - most importantly - not from rubber, which makes cleanup easier
4
December 1, 2021
Aaaand here goes the flash... or glacier sized plastic deposit, however you want to call it. It is removable, yet points towards potential fitting issues, as the molds seem to have been well used
5
December 1, 2021
Some assembly on the hull is done. I had to build one part of the rear door myself, but this is a general issue with these kits, as they do somehow not include a part to cover this hole in the door. Most work has been done in the rear, where I had to cut the one part rear panel to make it fit better
6
December 11, 2021
The finished model with the wheels left removable for painting. I had to scratch one of the front fender extensions and also had to do some filling, as there were molding imperfections present. The turrets recieved new bolts from streched sprue and visions port covers from styrene sheet.
7
December 11, 2021
The rear panel had to be cut to fit better and sanding was necessary on the sides, so I had to redo the stamped pattern on the boxes. I also added latches from plastic.
8
December 11, 2021
Towing hooks on the suspension elements had such thick sprue gates, that I did not manage to cut them without breaking. Thus I made replacements from wire. The tires had been given some more depth on their outer faces by cutting some grooves. In hindsight I maybe should have filled and completley redone the tire faces, but the result visible here hopefully suffices.
9
December 15, 2021
Things are in primer now... I used the rubber black from Tamiya not only for the tires, but also to darken some shadow or hard to reach areas
10
December 16, 2021
First coat is applied, the Hataka laquer did thin with Mr. Levelling Thinner, but when I added Tamiya Deck Tan to lightrn it up a little, I had slight splatters from the Tamiya paint... should have done more mixing and maybe add a tad of Tamiyas own retarder... but that is something to be considered later. First, I have to think about how to do the camo
11
December 18, 2021
The camouflage has been (more or less) sucessfully painted using another colour from Hataka made for French AFVs. I needed to add a little bit of retarder to prevent splattering/tip dry for me to be able to paint the brown lines properly
12
December 25, 2021
With the decals applied, I did some light chipping and added a pin-wash after coating the model in satin varnish. The decals were really hard to work with, as they did not really want to go off the sheet even in warm water...
13
December 25, 2021
Using Abteilung 502 oils, I tweaked the color in some areas and induced a "dusty look" on horizontal surfaces. The two rust washes were applied over the exhaust which has previously been painted with light grey acrylics.
14
December 27, 2021
Some dust weathering was done using one light dust coloured and one brown enamle paints mixed together to get a few colour variations. Also, a few stains were added with Engine Grime. Periscopes on the turret were given a gloss coat using Wet Effects.
15
December 27, 2021
The wheels recieved the same treatment with the dust colours, simulating the kind of deposits seen on vehicles travelling on dirt roads.
16
December 27, 2021
The top of thr/turret and some fender areas also recieved some more dust deposit-texture, as crews would walk on here

Kommentarer

12 1 December 2021, 20:46

Simon Nagorsnik
What can you say about the quality of the rpm kits?
Some flash is no problem but what about the details and the fitting?
Because I've never build one of these before

3 December 2021, 08:59

Tom B.
As for my kit, the fit was a little problematic in places, yet I can´t say if my sample is representative of their general quality. From what I´ve seen around the web, I may just have got a bad sample. Details are suprisingly fine, although some parts are more simplified than others.

3 December 2021, 17:17

Simon Nagorsnik
Thanks for reporting tom🙂
this gave me a better overview of this brand, I think I'll try one out too...

3 December 2021, 18:28

Robert Podkoński
Good work so far, Tom! I suppose the polistyrene is a bit soft...

15 December 2021, 20:19

Tom B.
Thank you 👍 The material isn´t as soft as I intially expected. It is in fact quite workable if it would not have that much flash...

15 December 2021, 20:28

Simon Nagorsnik
nice result so far, I hope you present it in a dio 😀

18 December 2021, 22:59

Tom B.
I am indeed thinking about presenting it on a little base with some White Stork Miniatures French tankers...

19 December 2021, 15:04

Tom B.
Edit: Although I am less sure about the figures to be quite honest, I would really like to a base. As the vehicle is in fact completely closed, I do think that leaving away figures and concentrating on doing some intricate basing work may in fact lead to the best results…

19 December 2021, 17:44

Album info

The Panhard 178 or Panhard AMD was a French pre-WW2 design of a heay armoured car weighing in at 8t. The vehicle ran on a 4x4 configuration and was armed with a 25mm high velocity gun enablng it to theoretically engaged lighter armoured vehicles, however it was mainly intended for reconnaissance duties. By the start of WW2, the vehicle was - though not bad - sheduled to be replaced by a new design called the Panhard AM 40P, this being the predecessor to the well known EBR. Even though it´s welded construction was anachronistic by the end of WW2, the French continued using an upgraded version with a new turret for a while.

The RPM kit is the only injection-molding offering of the Panhard 178 in 1/72 scale and is available in practically every version of the vehicle and is also rather cheap at below 8€. The box only contains two sprues with nice detail, although improvements can certainly be made. On my example, the used-molds phenomenon struck me again and I also ran into some fit issues...
Should I pull myself through to building another one, I would definetly deviate from the instructions a little during hull construction. Anyway, I am left with some gaps that can be left open (as it is the case on bolted vehicles versus welded ones), but some parts definetly need filling and redetailing. As any sanding will however destroy some rivets, I have to come up with a method of recreating them easily. At the moments, I gravitate towards stretched sprue.

After being more ore less sucessfull with the rivets, I will paint the model using Hataka laquers which is a first for me. On the plus side they have specific colours for 1930-1940s French AFVs.

Panhard AMD 178 Armoured Car

16 bilder

1:72

Avslutad

All albums

View all albums »